|
|
|
|
|---|
When replacing rail rubber cushions, it is important to get the right profile cushion for your pool table. Tables were designed to use one of four main types of rail cushion profiles. K66 profile is the most common and is used on most home and commercial 3 piece slate tables. K55 profile rail cushions are used on most coin operated tables and carom tables. U23 rail cushions are used on some home and commercial tables and Centennial or Century rail cushions are used on lower cost Brunswick and other lower cost home recreation pool tables.
Making sure you have the correct rail rubber cushion profile ensures that the cushion height or the rail strike point is in the proper position in relation to the ball. The rail height or stike point should be 63 1/2% of the ball diameter. (ex. standard pool ball is 2 1/4" in diameter, rail height should be .635 x 2.25 or 1.43" in height.)
By measuring the back side of the cushion, where it glues onto the rail which is dimensional height and measuring the top side of the rail cushion, which is top angle width and comparing these measurements with those dimensions listed below you can be sure to get the correct profile rubber cushion for your table. The tops and backs of the cushion usually have a cloth backing which helps to hold the profile shape.
Replacement set of K-66 profile rubber cushions. Available in 7,8 and 9 foot sizes. This is the most common of all cushions and found on most all major brands of billiard games. Quality cushions are made out of pure gum rubber and have cloth facings on top and back. 7 foot size is 36" long, 8 foot size is 43" and 9 foot size is 49".
Replacement set of K-55 profile rubber bumpers. Available in sizes to fit 7 or 8 foot and 9 foot billiards. These rubber bumpers are used most often on coin operated and carom billiard games. It has slightly larger dimensions than the more common K66 style. Quality bumpers are made out of pure gum rubber and have cloth facings on bumper top and back. Set of six 7-8 foot bumpers are 43 inches long and the 9 foot bumpers are 49" long.
Replacement set of U-23 profile rubber bumpers for all billiard games. This is a slightly smaller version of the popular K-66 style. Quality bumpers are made out of pure gum rubber and have cloth facings on top and back. Fits 7 and 8 foot sizes. Just cut to length you need. Set of 6 bumpers are 43 inches long each.
Replacement set of Centennial U-56 profile rubber bumpers for lower cost Brunswick and other lower cost tables that use the Centennial or Century profile cushions which are the same dimensions. This is a smaller and more triangular shape profile. These century cushions are made out of real rubber compounds for fast action tournament play. Fits 7 ,8 or 9 foot sizes. Just cut to length you need. Set of 6 bumpers are 48 inches long each.
These 100% gum rubber L-77 Canadian Step or "L" shape cushions provide superior playability. Pure gum rubber cushions last years longer than economy cushions with fillers. These are used on snooker tables and are available in 54", 60" or 72" in length. Six pieces per set.
Replacement rubber rail facings for all billiards. Set of 12 replaces all ends on rubber cushions. Just cut for a precise fit.
Double thick 1/4" replacement rubber rail facings for all billiards. Highest quality die cut over size facings used to close up the pocket size on pool tables that need the playing difficulty increased as in coin operated tables that have enlarged pocket holes. Closes pockets up to 1/4" inch. Make your home coin operated table play like a standard table with these extra thick cushion ends. Set of 12 replaces all ends on rubber cushions. Just cut for a precise fit.
Replacement rubber rail end cushions for all snooker tables. Set of 12 replaces all ends on rubber bumpers.
Locktite Contact Adhesive used for gluing replacement rubber bumpers, and bumper ends to rails. 5 fl oz tube.
Replacement set of 6 feather strips for all home billiards. Approximately 5/16" square tapered for a tight fit. Set of 6 wood feather strips fit up to 9 foot tables.
Rubber Feather Strip 6mm x 6mm. Featherstripping is used to tuck the cloth into the back of the rails. Rubber featherstripping holds the cloth in tighter and does not break. Sold in 25 foot lengths, this is enough for 7-9ft table sizes.
Bumper bolt removal tool for Brunswick. Makes these bolts easy to remove and replace.
Heavy rail mounting plate.
Crown Lock Washer is a spring washer used with vertical rail bolts through the slate. They prevent the rail bolts from coming loose and from cracking the slate.
Available are complete covered or uncovered pool table rail assemblies for coin operated billiard tables. These are exact duplicates of the original wood billiard rails complete with new rubber cushions glued on and ready for covering. These are also available as a option, precovered with standard billiard green felt. You may also optionally order these rails with a matching bed felt for a complete recovering kit.
Set of 18 Quality Replacement Rail Mounting Bolts For all Coin-Op Tables. Save yourself some grief by replacing your old, cross threaded bolts with these new quality bolts. Standard 1/4 - 20 size.
Sawtooth-style T-nuts for use with pool table rails. You won't find these thicker-gauge ultra-durable T-nuts in your local hardware store; these are the real deal and hold tight! 1/4 - 20 (standard) for all pool table rail brands except Global.
These new aluminum trim rails can make your Valley or Dynamo table look new again. These trim sets are made from extruded anodized aluminum and are very easy to install. Each set includes 4 pieces of trim and matching trim screws and fit Valley and Dynamo coin operated tables. Available for 7,8, and 9 foot tables and in aluminum, gold or black colors.
Bag of 100 trim screws used for attaching aluminum trim rails.
lakeside@moneymachines.com
Lakeside Distributors
We accept secure online credit card payments via Verisign Payment Services